• Was your home built before 1980? 
  • During this time period, building code regulations did not require wall insulation.
  • If your home was built during this time, it is likely that the walls are not insulated.
  • Are your walls cold to the touch?
  • Do you have high heating/cooling costs?
  • Do you have uneven heating/cooling within your home?
  • Does your furnace/air conditioner seem to run too much?
  • Do you notice mold growth in/on your walls?

How do I know if I need a Retrofit Drill & Fill? 

Spray Foam Insulation 


  • Makes your home more comfortable
  • Stops air and moisture infiltration
  • Does not require vapour barrier
  • Saves significantly on energy costs
  • High insulation value (R value) / rapid payback with energy savings
  • Adds strength to the building structure
  • It is permanent and will not sag
  • Keeps dust and pollen out
  • Eliminates Ice Damming
  • Improves Air Quality
  • Reduces capacity requirements, maintenance and wear of HVAC equipment
  • Meets all building codes
  • 100% vapour and moisture barrier

Our building envelope specialists offer services in Residential and Commercial applications, to save YOU and YOUR 

​Company $$$$!

WHAT DOES MR. INSULATION OFFER?

Mr. Insulation
266 County Road 42 Windsor , ON N8N3N2 CA
Phone: 519-962-6062 Website: www.mister-insulation.com

spray foam spray foam spray foam spray foam spray foam spray foam insulation spray foam insulation spray foam insulation spray foam insulation spray foam insulation attic insulation attic insulation attic insulation attic insulation attic insulation attic insulation mr insulation mr insulation mr insulation mr insulation mr insulation insulation contractors insulation contractors insulation contractors insulation contractors insulation contractors

  • With more than 25% of your heat loss coming out of your windows and doors, Mr. Insulation can cut that down to 0%. Making sure your Windows and Doors are completely sealed results in lower Heating and Cooling costs, which in turn can save you up to 25% of your original costs. 

If you have this problem, do not hesitate to call  Mr. Insulation for a free consultation!

  • Installed primarily in Residential conditions, if not installed properly, these Batts can leave you with Air Infiltrations resulting in high Heating & Cooling costs, and potential Mold growth if not pre-cautioned with exterior holes in the wall sheathing resulting in the transfer of water vapour from the outside to inside. 
  • Blankets have the same adverse effects, although these products are installed primarily in Basements and Crawl spaces on the foundation walls. 
  • Batt And Blanket Insulation is fairly easy to install, but if installed incorrectly it can lead to bigger problems in the future. As an inexpensive and professional choice, let Mr. Insulation help youwith all of your Insulation needs.


  • Retrofit Drill and Fill 
  • Window and Duct Sealing
  • Fiberglass Batt and Blanket Insulation

Retrofitting a house means upgrading it so it will "keep the heat in". During this process, small holes are drilled between wall studs and loose fill insulation is blown into the empty cavities. The holes are patched when completed. Loose fill insulation is a material called cellulose. 

This material can conform to any space without disturbing the existing structure (e.g. pre-existing enclosed walls).

This allows for the benefits of an upgrade without the inconvenience of a full scale remodel.

Drill and fill insulation can be installed internally through the home or externally through the outside of the home. Our trained technicians can insulate through drywall, brick, veneer, vinyl siding, lap wood siding, shipboard siding, wood based sheet siding, masonry, non-wood siding, stucco, gypsum board, plaster/lath and tile.

Call us today, for a free consultation.

  • Blown In Fiberglass & Cellulose Insulation

Cellulose and fiberglass are the two most popular types of blown insulation, and they each have some pros and cons. Here are some details on the differences between cellulose and fiberglass insulation.
Insulating Values
Cellulose and fiberglass have similar insulating values. Although cellulose does have a slightly higher R factor (cellulose has an R-value of approximately 3.0 per inch while fiberglass ranges from R-2.1 to R-2.7), cellulose will settle over time, potentially leaving some areas (in walls particularly) with little or no insulation. Fiberglass manufacturers have developed blown fiberglass insulation they claim won't settle over time.
Cellulose retains its insulating value no matter the temperature, however, fiberglass has been shown to lose some of its insulating value as the temperature drops. In extreme temperatures, the loss of insulating value can be as much as 50 percent.
Health Concerns
Loose-fill, or blown, cellulose insulation is manufactured primarily from recycled newspapers, a very benign product, so it poses virtually no ongoing health risk.
Blown fiberglass, on the other hand, is made up of very fine strands of glass, and these tiny fibers are a carcinogen that can easily be inhaled into your lungs. To offset this potential health concern, fiberglass insulation is usually covered with something after it's installed, or it's installed in an area where it won't be disturbed (such as an attic), so the fibers won't get into the air where they could be inhaled. With these precautions, it's no threat to your health.

Safety Concerns
Since cellulose is made from newspaper, it obviously will burn. Cellulose insulation manufacturers have responded to that concern by treating it with fire-retarding chemicals such as boric acid, ammonium sulfate, or sodium borate in the manufacturing process. These chemicals have the additional benefit of repelling mice and other rodents.
Fiberglass, on the other hand, because it's made from glass, simply won't burn (although it will melt at extremely high temperatures).
Other Factors
Cellulose contains the higher percentage of recycled materials. While the fiberglass industry does a good job of recycling and uses approximately 35 percent recycled material, cellulose manufacturers average over 75 percent recycled content.
Conclusion
Fiberglass insulation has proven over the years to provide effective temperature and sound insulation while more recently, cellulose has established itself as a viable alternative. Since either will do an effective job insulating your home, the insulation you choose should be based on other factors such as cost and availability of the product, quality and reputation of the installers (if you're not doing it yourself), and your personal environmental concerns.